The Conclusions and Recommendations may be combined or, in long reports, presented in separate sections.
Conclusions and recommendations
If there aren’t any recommendations to be produced as a consequence of the project, just call this section Conclusions.
The Conclusions section sums up one of the keys points of one’s discussion, the primary options that come with your design, or the significant outcomes of your investigation. As its function is to round from the story of your project, it should:
- be written to relate right to the aims regarding the project as previously mentioned within the Introduction
- indicate the extent to that your aims have already been achieved
- summarise the key findings, outcomes or information in your report
- acknowledge limitations and then make suggestions for future work (where applicable)
- highlight the importance or usefulness of your work.
The conclusions should relate to the aims for the work:
The goal of this project would be to design a mobile phone tower for a suburban location..
The cell phone tower presented here could be erected safely in a suburban street.
It needs a complete section of a maximum of 2m 2 l, and has now the following safety features.
This investigation will review the quantity of passengers making use of the Monash University Clayton-Caulfield inter-campus bus to be able to recommend adjustments to your ongoing service if required.
Analysis regarding the survey data obtained in this project reveals that usage of the Clayton-Caulfield inter-campus bus has grown by 24% in the past five years. It is recommended that frequency be increased during peak usage.
The Conclusions section below is from a known level 2 Civil Engineering Alternative Designs report presenting two designs for a an overpass bridge. Go through the coloured buttons to look at comments.
Conclusions
Each one of the two bridge designs Lecturer’s comment:
An elegant beginning for a Conclusions follows on neatly from the discussion that is preceding. In this case, it indicates that the aims for the project have already been met. presented in this report fulfil the criteria specified in the project brief. Both designs Lecturer’s comment:
The main findings or outcomes – in this case the key options that come with the designs – customwritings are then recapped. Incorporate piers that are round piled foundations, which are used because the soil conditions are unknown and perchance unstable. Design 1, an easy composite I-girder bridge, gets the benefit of being made from steel and so has longer spans and fewer piers.
Design 2, a beam that is super-T >Design 2 Lecturer’s comment:
The significance of the end result – in this instance the final recommendation – is clearly stated. is therefore recommended. It provides Lecturer’s comment:
To finish off, the achievement of the project is reinforced. an inexpensive overpass with superior durability, and fully meets the requirements of this design brief.
Always address limitations and suggest how they might be overcome in future work. The below that is excerpt from the Conclusions of a study on a project investigating the result of pulsation on heat transfer in horizontal pipe flow.
Experimental results Lecturer’s comment:
Key conclusions drawn from the project. showed that pulsed flow without flow reversal had no effect that is significant with steady flow. Preliminary experiments with reversed flow, however, clearly indicated increased heat transfer. This really is likely due Lecturer’s comment:
Provide a possible explanation for notable results, especially unexpected ones. to your large disturbances when you look at the hydrodynamic boundary layer as soon as the flow changes direction. Further research Lecturer’s comment:
Recommend further research to address any extra work you think will be useful. is advised to determine the utmost achievable enhancement.
It must be noted that Lecturer’s comment:
Acknowledge limitations or errors and suggest explanations and/or solutions. the experimental results usually do not concur with the equations that are theoretical. This can be as a result of the deposits which developed in the pipe, or even to inconsistent thermocouple temperature. Therefore, regular inspection of this test rig is preferred.
For a tremendously long report, it is acceptable to present the conclusions and recommendations in point form:
The prototype robot courier presented here has been confirmed to manage to delivering documents autonomously in an office environment. This has demonstrated the following components of mobile robotics:
- Localisation: The Kalman filter-based localisation algorithm achieved sub-centimeter accuracy under normal operating conditions.
- Environment modelling: The occupancy map was updated dynamically to include obstacles not included in the map that is original.
- Path planning: A distance path that is transform-based using obstacle transforms produced a globally optimal local entrapment-free road to the goal.